Previous: Foundation Walls          Next: Foundation Waterproofing

Foundation Insulation

With the foundation in place, the next step is applying the 12″ thick EPS insulation to the outside face of the concrete. (EPS is Expanded Polystyrene, often called bead board. It is a cheaper alternative to a related material called XPS, or Extruded Polystyrene, at the expense of a slightly lower R-value.) The insulation is glued to the foundation wall, and then covered with a waterproofing material to prevent damage to the insulation or unwanted water ingress.

OLYMPUS DIGITAL CAMERA

This is the insulation stash! This is the entire insulation package, excluding the sub-footing insulation already installed: foundation walls, footing sides, and under-slab.

 

OLYMPUS DIGITAL CAMERA

The footings are thermally protected on all sides. Concrete has a fairly poor R-value, so thermal bridges to the surrounding soil can be significant if you imagine the soil sitting at a constant ~8-10˚C all year, continuously sucking heat out of your house.

This strategy is somewhat different than many other Passive Houses that use a “raft slab” technique to insulate from the ground. The frost protection depth in this part of Alberta requires foundations to typically be 8′-0″ below grade. We’ve gone shallower to save material and money on concrete and insulation, though we’ll add an insulation skirt for additional frost protection once backfilling is underway.

 

OLYMPUS DIGITAL CAMERA

The crew hard at work, applying glue to the EPS.

 

OLYMPUS DIGITAL CAMERA

This is a view of the rear walk-out portion of the house. The top of the wall in the foreground will be roughly ground level when the house is complete.

 

OLYMPUS DIGITAL CAMERA

Close-up of the wall insulation being applied.

 

OLYMPUS DIGITAL CAMERA

The northwest wall…

 

OLYMPUS DIGITAL CAMERA

Detail of the shaped EPS profile at the footing, providing a continuous 12″ insulation layer around the footing.

 

OLYMPUS DIGITAL CAMERA

The northwest wall with profile attached.

 

OLYMPUS DIGITAL CAMERA

And the southeast wall.

OLYMPUS DIGITAL CAMERA

And a view from the front, showing the insulation on the inside of the garage. For the purposes of meeting the Passive House criteria, the garage is outside the thermal envelope of the house.

OLYMPUS DIGITAL CAMERA

The insulation is also applied to the interior as well. The basement slab will be well-insulated from below in pictures yet to come.

 



Previous: Foundation Walls          Next: Foundation Waterproofing

5 responses to “Foundation Insulation”

  1. What have you learned from this project that you would change on your net one?

    • cphadmin says:

      That probably deserves an entire post of its own once we get closer to completion (good idea). But at the moment I’d say I’d definitely do prefab wall construction next time. Way faster and better quality control. No doubt there will also be more PH materials readily available as the market matures and building codes evolve, so there may be more options for better assembly build-ups. [DZ]

  2. Jim Zeibin says:

    Hi George,
    This is a very good question and I agree with David re: it would be an entire post. Just some first thoughts though. I would go with a raft slab in the future instead of a footing separate from the slab. The EPS should be interlocked like T&G. In our case it wasn’t, leaving small gaps between pieces that needed to be filled later. I had a really good cribber, but he kind of did his own thing and didn’t follow the plans exactly. This resulted in me having to do a lot of EPS cutting which is no fun when it is 12″ thick. The wall assemblies worked well although there would be improved efficiencies of prefabbing these as mentioned above. Reduce the amount of gusseting as the walls were extra strong. One thing I would change is the use of the SIGA Rissan tape for air sealing. This tape is excellent to work with. We did a preliminary blower door test and ended up averaging 0.15ACH which exceeded our expectations. I would not change the quality of windows neither. They are fantastic.

  3. Jim, Dave, I’m absolutely etatic over the execution of this project. There are many Passive House projects appearing on the net and I must say that most are lost in what they think is the correct approach to the final outcome.

    The use of EPS is in my mine one of the most important choice of materials that the Architect and Builder has in their toolbox. That said the understanding of how this seemingly odd building material is used to its best potential, is where some get it wrong. If we cam use it for airport runways and floating house foundations, everything else is a cakewalk.

    I have over 80,000 construction photos of EPS Construction
    sequences that I would be happy to offer if you need some ideas strengthened for future projects.

  4. Jim Zeibin says:

    Thanks George,

    EPS is indeed a wonderful project. It is easy to shape and form and has so many potential uses. I worked in a styrene plant early in my career and had a good experience with it. It was definitely interesting to hear people’s comments when we said that we put it under the footings. As this is our retirement home, I’m thinking this might be my last project, but one never knows.
    Regards,

Leave a Reply

Your email address will not be published. Required fields are marked *